Bevel gearboxes and flanged bevel gearboxes for indicators

Home > Products > Transmission of motion, regulation of speed and position, lifting, displacement and alignment > Bevel gearboxes and flanged bevel gearboxes for indicators > 66/22

Tutti i prodotti

66/22

Gearboxes for intermittent use

66/22

Gearboxes for intermittent use

• Aluminium case, black anodised; stainless steel shafts.
• Available with reduction ratio: 1:1.
• Torque 2 Nm. Radial load 7,5 kg - axial load 0,7 kg.
• Models:
- Version «A» with 2 outputs; weight 50 g.
- Version «B» with 3 outputs; weight 65 g.
- Version «C» (opposite rotation) with 3 ouputs; weight 65 g.
• Output shafts: <M> = male Ø6 / <F> = female Ø6.
Available on request:
▪ Output shafts: <F> = female Ø8 - Ø10 (only for version «A»)
▪Models with spiral bevel gears are available in all versions.
▪ Grease fitting is available in all versions.
▪ Machine-side coupling flange FL-M.
▪ Male shaft flange for position indicators FL-OP/EP.

Photogallery

APPLICATION EXAMPLES

AVAILABLE SHAFTS
M = male Ø6	F = female Ø6	F = female ø8/ø10

DIMENSIONS

VERSIONS ⟪A⟫ - M-M

VERSIONS ⟪A⟫ - M-F

VERSIONS ⟪A⟫ - F-M

VERSIONS ⟪A⟫ - F-F

VERSIONS ⟪A⟫ - F(Ø8)-F(Ø8)

VERSIONS ⟪A⟫ - F(Ø10)-F(Ø10)

VERSIONS ⟪B⟫ - M-M-M

VERSIONS ⟪B⟫ - M-F-F

VERSIONS ⟪B⟫ - F-M-M

VERSIONS ⟪B⟫ - F-F-F

VERSIONS ⟪C⟫ - M-M-M con rotazione contraria

VERSIONS ⟪C⟫ - M-F-F con rotazione contraria

VERSIONS ⟪C⟫ - F-M-M con rotazione contraria

VERSIONS ⟪C⟫ - F-F-F con rotazione contraria

CONFIGURATION AND DIRECTION OF ROTATION

Tab.1

AVAILABLE VERSIONS
⟪A⟫	⟪B⟫	⟪C⟫

2 outputs, same rotation direction	3 outputs, same rotation direction	3 outputs, 1 with opposite rotation directions

OUTPUT SHAFT IDENTIFICATION

Tab.2

AVAILABLE OUTPUT SHAFTS
male = M	female blind = F	through female = F

Example with 2 outputs	Example with 3 outputs

REFERENCE RULES
Shaft 1 is always shown on the side opposite the M_1 fixing bores and serves as the reference for determining:
● the configuration
● the direction of rotation
By convention, Shaft 1is shown rotating clockwise. The others shaft are defined following the clockwise direction.

M_ FIXING POSITIONS

Tab.4

Shaft 1 remains the reference and is conventionally shown rotating clockwise; the housing is rotated by 90° from the previous position.

M_1 = top view. 0°			M_2 = right side view 90°
		+90° → DX
same rotation	opposite rotation		same rotation	opposite rotation
↑ +90°			+90° ↓
M_3 = left side view 270°			M_4 = bottom view 180°
		+90° ← SX
same rotation	opposite rotation		same rotation	opposite rotation

GREASE NIPPLE POSITION

Tab.5

Gearboxes with 2 shafts	Gearboxes with 3 shafts

For model 66/22 and 66/8 only: recommended for demanding conditions or extended service life. Periodically replenish the lubricant as instructed by our Technical Department. Supplied in the standard position shown; other positions on request.

COUPLING BUSHES 2 piece bushing to couple gearboxes and shafts.

Available bores Ø: 6 - 8 -10 -14.
➜ for more complete information, see BT

Support units (with square flange) with o.ring, and ball-bearings.

• Available shafts Ø6, Ø8, Ø10, Ø14, Ø20.
➜ for more complete information, see Supports

Flanged supports with extension shaft for coupling with position indicators.
➜ for more complete information, see Flanged supports

The «GC» and «GCC» cardan joints used for the transmission of torque and movement of non-aligned elements.
Main features: universal application, high reliability, maintenance free, extremely precise and ease-of-use.
• Case entirely machined from solid, in stainless steel AISI303.
• Suitable for intermittent (UI) and continuous movements (UC).
• Maximum working angle 45 °.

➜ for more complete information, see GC and GCC

• 3 digits counter (standard red digit indicates decimals; on request 2 red digits for hundredths or 3 black digits for mm). Reading until 999. Digit height 6 mm
• Particularly suitable for little adjustments in small spaces.
• Standard shaft bore Ø8, Ø10 or Ø12.

➜ for more complete information, see OP2

The FL-M machine-side coupling flange, compatible with any configuration and shaft (male or female) of the gearbox, ensures a stable and precise coupling, minimizing vibrations and ensuring correct alignment between the connected components.
Made of black anodized aluminum, it is coordinated with the gearbox case, also in black

FL-M

Configuration examples
Gearbox with 2 shafts	Gearbox with 3 shafts

Male shaft with flange MØ8x55 FL-OP2, compatible with any configuration and shaft of the gearbox, connects the position indicator, whether mechanical or electronic, to the gearbox. This combination enables precise and monitored position adjustment, increasing stability and accuracy of readings. Made of black anodized aluminum, it is coordinated with the gearbox case, also in black.