RD26

Right - Angle gear reducer




Highly compact reducer for various industrial applications, in particular for automation and robotics; applicable also to motors.
• Housing made of anodized aluminium, shafts made of steel with surface hardening treatment (high wear and corrosion resistance).
• Standard transmission ratios: 1/1 - 1/2 - 1/3 - 1/4 - 1/5- 1/7,5 - 1/10 - 1/15 - 1/25 - 1/30
• Several mounting options with protruding / hollow input and output shafts.
• Flanges for direct connection to machine, motors and display with position indicators.
• Available versions:
- RD26 Gear reducer
- RD26F for threaded shaft (shaft not supplied)
- RD26S with magnetic sensor
- RD26M with permanent magnet motor
- RD26MS with permanent magnet motor and magnetic sensor
- RD26MR with gearmotor
- RD26MRS with gearmotor and magnetic sensor

 For sensor and motor data, see the "General Technical Data" section in the drop-down menu on the right. 

 



 


Photogallery

RD26
1. N° 3 shaft lock pins M3 at 120°
2. Threaded M3x6 

 

RD26F for THREADED OUTPUT SHAFT (shaft not supplied)
 





SENSOR DATA FOR RD26

Dimensions

12 x 26 x 26 cm 

Power supply

10 ÷ 30 Vdc ±10%, max 60 mA

Accuracy

256 pulses/rev

Max. current ouput

channels A - B (20mA)

Protection degree

IP66

Case

anodized aluminium 

Working temperature

-10 ÷ 70 °C

Working humidity

10 ÷90%

Cable output

0,5 - 1 -2 -5 -10 meters 

EMC

2004/108/CE

The sensor converts the rotation output shaft of the gearbox 

 

MOTORS FOR RD26
   

MOTORS "M" WITH COUPLING FOR RD26

GEARMOTORS "MR" WITH COUPLING FOR RD26
 A RPM  TORQUE (Nm)   A RPM  TORQUE (Nm) 
 35  56  2200  0,06  30 79  450  0,4 
 35  65  11000  0,05  

 suitable for alternate movements

 suitable for continuous movements

 

AVAILABLE VERSIONS
 RD26 reducer RD26F for threaded shaft RD26S with sensor
     
RD26M with motor  RD26MR with gearmotor
   
RD26MS with motor & sensor RD26MRS with gearmotor & sensor
   

 

 

Access to Reserved Area

Did you forget your password?


Richiedi l'accesso




*Required replies

TECHNICAL FEATURES
FA = input axial load 20 N
FA = ouput axial load 20 N
FR = input radial load 100 N
FR = output radial load 200N
Max. backlash 0,75°
Max input rpm (1/min) 5.000
Working temperature -20 +90°
Life 10.000 h
Weight 80 gr
Lubrication  grease Klüber AG 11-462


EFFICIENCY TABLE
i 1/1 1/2 1/3 1/4 1/5 1/7,5 1/10 1/12,5 1/15 1/25 1/30
R    % 0,72 0,72 0,69 0,63 0,60 0,61 0,55 0,39 0,45 0,25 0,30

TI  Nm

4,18 2,07 1,46 1,19 1 0,66 0,55 0,61 0,44 0,48 0,34
TO Nm 3 3 3 3 3 3 3 3 3 3 3

 irreversibility

Legend:
i   = transmission ratio
R  = efficiency 
TI  = input torque
TO = output torque

 

In case of continuous use, please contact our Technical Dept. In such applications, a grease fitting will be installed to allow periodic addition  of lubricant with a frequency based on the work conditions.

⁃ To identify the most suitable gear reducer for your requirements, refer to the values in the table. If the real loads and efficiency are very close to the table values, contact the technical department.
⁃ All tables show linear measurements expressed in <mm>, unless otherwise specified.
⁃ All the reduction ratios are expressed as a <fraction> unless otherwise specified.
⁃ All forces, efficiency and the loads are expressed in <N or Nm> (10 N ≅ 1 kg or 10Nm ≅ 1Kgm ) unless otherwise specified.